MR JUMP, a well-known name among fans of motocross & of all having a favor for mud, sand & jumps. A tri-composite fiber shell as strong as light, available in three different EPS sizes & with modular cheek pads, this helmet gives every off-road rider the chance to find the right comfort, the essential feature necessary to face the off-road activity with the required concentration. The wide window ensures the maximum visibility & a great air inflow even at low speeds. &, because it’s important to have a helmet that represents the personality of each rider, Suomy added new appealing & trendy graphics which follow the market demands. Features TRICARBOCO shell Shell in two

Sizes: M & L Protective polystyrene in 3 sizes Optimized ventilation thanks to the polystyrene grooves Internal upholstery in fabric Internal removable cheek pads Double D-Ring retention system Easily adjustable peak Weight: 999 ± 50 gr. Homologation ECE 22-05 Shell The shell is made from TRICARBOCO fiber, a new composite that allows to obtain a lighter shell but at the same time harder & more protective. The new composite is a mixture of carbon with different weight/breaking loads linked up with aramid resins that ensure a light shell but much more resistant to impacts. To satisfy even the most exigent customers, SPEEDSTAR is produced in two different shell

Sizes: M & L. Protective Polystyrene Internal Polystyrene liner is realized in three sizes (S, M & L) to obtain a better ergonomics & a variable density. This characteristic allows a gradual & progressive absorption of the power produced by the impact. Even if the bigger part of the energy created by the impact is absorbed by the external shell, thanks to its deformation, the role of Polystyrene is crucial for the absorption of the residual power. A different density of the polystyrene allows to optimize the mechanical performance of the shell-polystyrene, ensuring the maximum level of absorption in all areas of the helmet. Ventilation The air intakes were designed to improve the internal comfort. The airflow is channeled by 4 front intakes, protected by a metal grid. The Internal polystyrene was designed to work in symbiosis with the air intakes in the external shell. Particular channels obtained in the polystyrene, permit an optimized airflow & a quick exhaust of the hot air. Air Vents: Effective top & chin vents, rear exhaust port Channeled EPS: Canalization of the inner shell to guarantee the maximum heat transport Interior Cheek pads & inner liner can be removed, washed & replaced. The inner lining is made from a fine stretch

Fabric: High resistance to abrasion Sweat Absorption Antibacterial Treatment Keep fresh & dry Light fabric, soft & breathable Retention system Retention system with light alloy ” Double D-Ring”. Peak The peak has an elongated, protective profile & is easily adjustable to multiple positions without using tools. Mask fit The perimeter of the window is designed to offer a wide view & provides a comfortable housing for the most different types of motocross goggles. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default





...

MR JUMP, a well-known name among fans of motocross & of all having a favor for mud, sand & jumps. A tri-composite fiber shell as strong as light, available in three different EPS sizes & with modular cheek pads, this helmet gives every off-road rider the chance to find the right comfort, the essential feature necessary to face the off-road activity with the required concentration. The wide window ensures the maximum visibility & a great air inflow even at low speeds. &, because it’s important to have a helmet that represents the personality of each rider, Suomy added new appealing & trendy graphics which follow the market demands. Features TRICARBOCO shell Shell in two

Sizes: M & L Protective polystyrene in 3 sizes Optimized ventilation thanks to the polystyrene grooves Internal upholstery in fabric Internal removable cheek pads Double D-Ring retention system Easily adjustable peak Weight: 999 ± 50 gr. Homologation ECE 22-05 Shell The shell is made from TRICARBOCO fiber, a new composite that allows to obtain a lighter shell but at the same time harder & more protective. The new composite is a mixture of carbon with different weight/breaking loads linked up with aramid resins that ensure a light shell but much more resistant to impacts. To satisfy even the most exigent customers, SPEEDSTAR is produced in two different shell

Sizes: M & L. Protective Polystyrene Internal Polystyrene liner is realized in three sizes (S, M & L) to obtain a better ergonomics & a variable density. This characteristic allows a gradual & progressive absorption of the power produced by the impact. Even if the bigger part of the energy created by the impact is absorbed by the external shell, thanks to its deformation, the role of Polystyrene is crucial for the absorption of the residual power. A different density of the polystyrene allows to optimize the mechanical performance of the shell-polystyrene, ensuring the maximum level of absorption in all areas of the helmet. Ventilation The air intakes were designed to improve the internal comfort. The airflow is channeled by 4 front intakes, protected by a metal grid. The Internal polystyrene was designed to work in symbiosis with the air intakes in the external shell. Particular channels obtained in the polystyrene, permit an optimized airflow & a quick exhaust of the hot air. Air Vents: Effective top & chin vents, rear exhaust port Channeled EPS: Canalization of the inner shell to guarantee the maximum heat transport Interior Cheek pads & inner liner can be removed, washed & replaced. The inner lining is made from a fine stretch

Fabric: High resistance to abrasion Sweat Absorption Antibacterial Treatment Keep fresh & dry Light fabric, soft & breathable Retention system Retention system with light alloy ” Double D-Ring”. Peak The peak has an elongated, protective profile & is easily adjustable to multiple positions without using tools. Mask fit The perimeter of the window is designed to offer a wide view & provides a comfortable housing for the most different types of motocross goggles. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default





...

MR JUMP, a well-known name among fans of motocross & of all having a favor for mud, sand & jumps. A tri-composite fiber shell as strong as light, available in three different EPS sizes & with modular cheek pads, this helmet gives every off-road rider the chance to find the right comfort, the essential feature necessary to face the off-road activity with the required concentration. The wide window ensures the maximum visibility & a great air inflow even at low speeds. &, because it’s important to have a helmet that represents the personality of each rider, Suomy added new appealing & trendy graphics which follow the market demands. Features TRICARBOCO shell Shell in two

Sizes: M & L Protective polystyrene in 3 sizes Optimized ventilation thanks to the polystyrene grooves Internal upholstery in fabric Internal removable cheek pads Double D-Ring retention system Easily adjustable peak Weight: 999 ± 50 gr. Homologation ECE 22-05 Shell The shell is made from TRICARBOCO fiber, a new composite that allows to obtain a lighter shell but at the same time harder & more protective. The new composite is a mixture of carbon with different weight/breaking loads linked up with aramid resins that ensure a light shell but much more resistant to impacts. To satisfy even the most exigent customers, SPEEDSTAR is produced in two different shell

Sizes: M & L. Protective Polystyrene Internal Polystyrene liner is realized in three sizes (S, M & L) to obtain a better ergonomics & a variable density. This characteristic allows a gradual & progressive absorption of the power produced by the impact. Even if the bigger part of the energy created by the impact is absorbed by the external shell, thanks to its deformation, the role of Polystyrene is crucial for the absorption of the residual power. A different density of the polystyrene allows to optimize the mechanical performance of the shell-polystyrene, ensuring the maximum level of absorption in all areas of the helmet. Ventilation The air intakes were designed to improve the internal comfort. The airflow is channeled by 4 front intakes, protected by a metal grid. The Internal polystyrene was designed to work in symbiosis with the air intakes in the external shell. Particular channels obtained in the polystyrene, permit an optimized airflow & a quick exhaust of the hot air. Air Vents: Effective top & chin vents, rear exhaust port Channeled EPS: Canalization of the inner shell to guarantee the maximum heat transport Interior Cheek pads & inner liner can be removed, washed & replaced. The inner lining is made from a fine stretch

Fabric: High resistance to abrasion Sweat Absorption Antibacterial Treatment Keep fresh & dry Light fabric, soft & breathable Retention system Retention system with light alloy ” Double D-Ring”. Peak The peak has an elongated, protective profile & is easily adjustable to multiple positions without using tools. Mask fit The perimeter of the window is designed to offer a wide view & provides a comfortable housing for the most different types of motocross goggles. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default





...

MR JUMP, a well-known name among fans of motocross & of all having a favor for mud, sand & jumps. A tri-composite fiber shell as strong as light, available in three different EPS sizes & with modular cheek pads, this helmet gives every off-road rider the chance to find the right comfort, the essential feature necessary to face the off-road activity with the required concentration. The wide window ensures the maximum visibility & a great air inflow even at low speeds. &, because it’s important to have a helmet that represents the personality of each rider, Suomy added new appealing & trendy graphics which follow the market demands. Features TRICARBOCO shell Shell in two

Sizes: M & L Protective polystyrene in 3 sizes Optimized ventilation thanks to the polystyrene grooves Internal upholstery in fabric Internal removable cheek pads Double D-Ring retention system Easily adjustable peak Weight: 999 ± 50 gr. Homologation ECE 22-05 Shell The shell is made from TRICARBOCO fiber, a new composite that allows to obtain a lighter shell but at the same time harder & more protective. The new composite is a mixture of carbon with different weight/breaking loads linked up with aramid resins that ensure a light shell but much more resistant to impacts. To satisfy even the most exigent customers, SPEEDSTAR is produced in two different shell

Sizes: M & L. Protective Polystyrene Internal Polystyrene liner is realized in three sizes (S, M & L) to obtain a better ergonomics & a variable density. This characteristic allows a gradual & progressive absorption of the power produced by the impact. Even if the bigger part of the energy created by the impact is absorbed by the external shell, thanks to its deformation, the role of Polystyrene is crucial for the absorption of the residual power. A different density of the polystyrene allows to optimize the mechanical performance of the shell-polystyrene, ensuring the maximum level of absorption in all areas of the helmet. Ventilation The air intakes were designed to improve the internal comfort. The airflow is channeled by 4 front intakes, protected by a metal grid. The Internal polystyrene was designed to work in symbiosis with the air intakes in the external shell. Particular channels obtained in the polystyrene, permit an optimized airflow & a quick exhaust of the hot air. Air Vents: Effective top & chin vents, rear exhaust port Channeled EPS: Canalization of the inner shell to guarantee the maximum heat transport Interior Cheek pads & inner liner can be removed, washed & replaced. The inner lining is made from a fine stretch

Fabric: High resistance to abrasion Sweat Absorption Antibacterial Treatment Keep fresh & dry Light fabric, soft & breathable Retention system Retention system with light alloy ” Double D-Ring”. Peak The peak has an elongated, protective profile & is easily adjustable to multiple positions without using tools. Mask fit The perimeter of the window is designed to offer a wide view & provides a comfortable housing for the most different types of motocross goggles. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default





...

MR. JUMP, the fiber helmet studied in details for comfort, technology & for sure safety for end user. It has been studied & tested to optimize the outside & inside air flows. OUTER SHELL in tricarboco material, mix of Kevlar, carbon & fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell

Sizes: XS-L & XL-2XL INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M & L). The special shape & construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation. The D-RING RETENTION SYSTEM has been designed & patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back & rotating it to the front it cannot be removed & it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained & repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position & properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button & pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471 CHEEK PADS completely removable & washable, with different thickness to get a perfect customization od the helmet. INTERNAL SHELL completely removable & washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet & to let off the hot air through the back part. INNER (cheek pads & inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry & comfortable. Lightweight, soft & breathable fabric. Performance verified & certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper & back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation. The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses. weigth: ca. 1000gr Note Please note that as long as nothing else is written in the article description, all helmets that have a visor as standard will be delivered with a clear one, even if it is shown differently.

...

MR. JUMP, the fiber helmet studied in details for comfort, technology & for sure safety for end user. It has been studied & tested to optimize the outside & inside air flows. OUTER SHELL in tricarboco material, mix of Kevlar, carbon & fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell

Sizes: XS-L & XL-2XL INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M & L). The special shape & construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation. The D-RING RETENTION SYSTEM has been designed & patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back & rotating it to the front it cannot be removed & it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained & repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position & properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button & pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471 CHEEK PADS completely removable & washable, with different thickness to get a perfect customization od the helmet. INTERNAL SHELL completely removable & washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet & to let off the hot air through the back part. INNER (cheek pads & inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry & comfortable. Lightweight, soft & breathable fabric. Performance verified & certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper & back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation. The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses. weigth: ca. 1000gr Note Please note that as long as nothing else is written in the article description, all helmets that have a visor as standard will be delivered with a clear one, even if it is shown differently.

...

MR. JUMP, the fiber helmet studied in details for comfort, technology & for sure safety for end user. It has been studied & tested to optimize the outside & inside air flows. OUTER SHELL in tricarboco material, mix of Kevlar, carbon & fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell

Sizes: XS-L & XL-2XL INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M & L). The special shape & construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation. The D-RING RETENTION SYSTEM has been designed & patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back & rotating it to the front it cannot be removed & it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained & repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position & properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button & pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471 CHEEK PADS completely removable & washable, with different thickness to get a perfect customization od the helmet. INTERNAL SHELL completely removable & washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet & to let off the hot air through the back part. INNER (cheek pads & inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry & comfortable. Lightweight, soft & breathable fabric. Performance verified & certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper & back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation. The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses. weigth: ca. 1000gr Note Please note that as long as nothing else is written in the article description, all helmets that have a visor as standard will be delivered with a clear one, even if it is shown differently.

...

MR. JUMP, the fiber helmet studied in details for comfort, technology & for sure safety for end user. It has been studied & tested to optimize the outside & inside air flows. OUTER SHELL in tricarboco material, mix of Kevlar, carbon & fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell

Sizes: XS-L & XL-2XL INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M & L). The special shape & construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation. The D-RING RETENTION SYSTEM has been designed & patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back & rotating it to the front it cannot be removed & it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained & repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position & properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button & pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471 CHEEK PADS completely removable & washable, with different thickness to get a perfect customization od the helmet. INTERNAL SHELL completely removable & washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet & to let off the hot air through the back part. INNER (cheek pads & inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry & comfortable. Lightweight, soft & breathable fabric. Performance verified & certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper & back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation. The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses. weigth: ca. 1000gr Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default

...

Replacement lining for Suomy helmets. Suitable for Suomy Mr Jump ...

Replacement lining for Suomy helmets. Suitable for Suomy Mr Jump ...