The Quantum 2 WB jacket is for riders who want sport performance with an urban flavor. It s graphics echo the other pieces from Quantum collection making sure individuals who want to stand out do. This hooded jacket’ s exterior is made from abrasion-resistant softshell 3L for ease of movement & for peace of mind while on the road. & making sure cold air stays out & riders stay warm, REV IT! incorporated the Hydratex® Wind Barrier® to do the job. SEESMART™ Level 1 armor is found at the shoulders & elbows, & for those who want a protective upgrade, it comes with a pocket that’ s prepared for the Level 2 back protector insert. Features Race fit Elasticated waist Inner pocket Two slit pockets on front Jeans loop
- The loop at the back of this jacket enables you to attach it to your jeans, which prevents the jacket from creeping up: no more exposed back when riding your bike. Short connection zipper Knitted cuffs at outer jacket Stretchable cuff Thumb loops Wind catcher behind front zipper
- Behind the front a panel has been installed to block the wind. This garment is certified according to the EN 17092 Standard, published in 2020 & has achieved A rating. Outer garment Softshell 3L Insulation Hydratex® Wind Barrier®
- The REV’IT! Wind Barrier® membrane is laminated between two separate layers of

Fabric: a stretchable outer layer, & a soft fleece inner layer. This combination blocks against wind & helps repel water. Stopping the wind & rain helps prevent hypothermia, & improves a rider’s level of comfort & warmth. Protection Prepared for SEESOFT™ Level 2 back protector insert
- Type RV SEESMART™ RV32-L1-B on elbow SEESMART™ RV31-L1-B on shoulder





...

The Quantum 2 WB jacket is for riders who want sport performance with an urban flavor. It s graphics echo the other pieces from Quantum collection making sure individuals who want to stand out do. This hooded jacket’ s exterior is made from abrasion-resistant softshell 3L for ease of movement & for peace of mind while on the road. & making sure cold air stays out & riders stay warm, REV IT! incorporated the Hydratex® Wind Barrier® to do the job. SEESMART™ Level 1 armor is found at the shoulders & elbows, & for those who want a protective upgrade, it comes with a pocket that’ s prepared for the Level 2 back protector insert. Features Race fit Elasticated waist Inner pocket Two slit pockets on front Jeans loop
- The loop at the back of this jacket enables you to attach it to your jeans, which prevents the jacket from creeping up: no more exposed back when riding your bike. Short connection zipper Knitted cuffs at outer jacket Stretchable cuff Thumb loops Wind catcher behind front zipper
- Behind the front a panel has been installed to block the wind. This garment is certified according to the EN 17092 Standard, published in 2020 & has achieved A rating. Outer garment Softshell 3L Insulation Hydratex® Wind Barrier®
- The REV’IT! Wind Barrier® membrane is laminated between two separate layers of

Fabric: a stretchable outer layer, & a soft fleece inner layer. This combination blocks against wind & helps repel water. Stopping the wind & rain helps prevent hypothermia, & improves a rider’s level of comfort & warmth. Protection Prepared for SEESOFT™ Level 2 back protector insert
- Type RV SEESMART™ RV32-L1-B on elbow SEESMART™ RV31-L1-B on shoulder





...

The Quantum 2 WB jacket is for riders who want sport performance with an urban flavor. It s graphics echo the other pieces from Quantum collection making sure individuals who want to stand out do. This hooded jacket’ s exterior is made from abrasion-resistant softshell 3L for ease of movement & for peace of mind while on the road. & making sure cold air stays out & riders stay warm, REV IT! incorporated the Hydratex® Wind Barrier® to do the job. SEESMART™ Level 1 armor is found at the shoulders & elbows, & for those who want a protective upgrade, it comes with a pocket that’ s prepared for the Level 2 back protector insert. Features Race fit Elasticated waist Inner pocket Two slit pockets on front Jeans loop
- The loop at the back of this jacket enables you to attach it to your jeans, which prevents the jacket from creeping up: no more exposed back when riding your bike. Short connection zipper Knitted cuffs at outer jacket Stretchable cuff Thumb loops Wind catcher behind front zipper
- Behind the front a panel has been installed to block the wind. This garment is certified according to the EN 17092 Standard, published in 2020 & has achieved A rating. Outer garment Softshell 3L Insulation Hydratex® Wind Barrier®
- The REV’IT! Wind Barrier® membrane is laminated between two separate layers of

Fabric: a stretchable outer layer, & a soft fleece inner layer. This combination blocks against wind & helps repel water. Stopping the wind & rain helps prevent hypothermia, & improves a rider’s level of comfort & warmth. Protection Prepared for SEESOFT™ Level 2 back protector insert
- Type RV SEESMART™ RV32-L1-B on elbow SEESMART™ RV31-L1-B on shoulder





...

The Quantum 2 WB jacket is for riders who want sport performance with an urban flavor. It s graphics echo the other pieces from Quantum collection making sure individuals who want to stand out do. This hooded jacket’ s exterior is made from abrasion-resistant softshell 3L for ease of movement & for peace of mind while on the road. & making sure cold air stays out & riders stay warm, REV IT! incorporated the Hydratex® Wind Barrier® to do the job. SEESMART™ Level 1 armor is found at the shoulders & elbows, & for those who want a protective upgrade, it comes with a pocket that’ s prepared for the Level 2 back protector insert. Features Race fit Elasticated waist Inner pocket Two slit pockets on front Jeans loop
- The loop at the back of this jacket enables you to attach it to your jeans, which prevents the jacket from creeping up: no more exposed back when riding your bike. Short connection zipper Knitted cuffs at outer jacket Stretchable cuff Thumb loops Wind catcher behind front zipper
- Behind the front a panel has been installed to block the wind. This garment is certified according to the EN 17092 Standard, published in 2020 & has achieved A rating. Outer garment Softshell 3L Insulation Hydratex® Wind Barrier®
- The REV’IT! Wind Barrier® membrane is laminated between two separate layers of

Fabric: a stretchable outer layer, & a soft fleece inner layer. This combination blocks against wind & helps repel water. Stopping the wind & rain helps prevent hypothermia, & improves a rider’s level of comfort & warmth. Protection Prepared for SEESOFT™ Level 2 back protector insert
- Type RV SEESMART™ RV32-L1-B on elbow SEESMART™ RV31-L1-B on shoulder





...

The Quantum 2 WB jacket is for riders who want sport performance with an urban flavor. It s graphics echo the other pieces from Quantum collection making sure individuals who want to stand out do. This hooded jacket’ s exterior is made from abrasion-resistant softshell 3L for ease of movement & for peace of mind while on the road. & making sure cold air stays out & riders stay warm, REV IT! incorporated the Hydratex® Wind Barrier® to do the job. SEESMART™ Level 1 armor is found at the shoulders & elbows, & for those who want a protective upgrade, it comes with a pocket that’ s prepared for the Level 2 back protector insert. Features Race fit Elasticated waist Inner pocket Two slit pockets on front Jeans loop
- The loop at the back of this jacket enables you to attach it to your jeans, which prevents the jacket from creeping up: no more exposed back when riding your bike. Short connection zipper Knitted cuffs at outer jacket Stretchable cuff Thumb loops Wind catcher behind front zipper
- Behind the front a panel has been installed to block the wind. This garment is certified according to the EN 17092 Standard, published in 2020 & has achieved A rating. Outer garment Softshell 3L Insulation Hydratex® Wind Barrier®
- The REV’IT! Wind Barrier® membrane is laminated between two separate layers of

Fabric: a stretchable outer layer, & a soft fleece inner layer. This combination blocks against wind & helps repel water. Stopping the wind & rain helps prevent hypothermia, & improves a rider’s level of comfort & warmth. Protection Prepared for SEESOFT™ Level 2 back protector insert
- Type RV SEESMART™ RV32-L1-B on elbow SEESMART™ RV31-L1-B on shoulder





...

The Quantum 2 WB jacket is for riders who want sport performance with an urban flavor. It s graphics echo the other pieces from Quantum collection making sure individuals who want to stand out do. This hooded jacket’ s exterior is made from abrasion-resistant softshell 3L for ease of movement & for peace of mind while on the road. & making sure cold air stays out & riders stay warm, REV IT! incorporated the Hydratex® Wind Barrier® to do the job. SEESMART™ Level 1 armor is found at the shoulders & elbows, & for those who want a protective upgrade, it comes with a pocket that’ s prepared for the Level 2 back protector insert. Features Race fit Elasticated waist Inner pocket Two slit pockets on front Jeans loop
- The loop at the back of this jacket enables you to attach it to your jeans, which prevents the jacket from creeping up: no more exposed back when riding your bike. Short connection zipper Knitted cuffs at outer jacket Stretchable cuff Thumb loops Wind catcher behind front zipper
- Behind the front a panel has been installed to block the wind. This garment is certified according to the EN 17092 Standard, published in 2020 & has achieved A rating. Outer garment Softshell 3L Insulation Hydratex® Wind Barrier®
- The REV’IT! Wind Barrier® membrane is laminated between two separate layers of

Fabric: a stretchable outer layer, & a soft fleece inner layer. This combination blocks against wind & helps repel water. Stopping the wind & rain helps prevent hypothermia, & improves a rider’s level of comfort & warmth. Protection Prepared for SEESOFT™ Level 2 back protector insert
- Type RV SEESMART™ RV32-L1-B on elbow SEESMART™ RV31-L1-B on shoulder





...

Engineered to perform, built to last & to protect, the long-cuffed Quantum 2 gloves have been designed to look great with any one-piece suits or sport jackets in the REV IT! Quantum collection. Race-spec knuckles, finger, palm, & cuff protection & sliders, are just a few incorporated features. Supple yet strong drum dyed goatskin & cowhide leather & stretch panels protect hands & allow for freedom of movement. An adjustment strap at the wrist & an adjustment tab at the cuff ensure the Quantum 2 gloves stay secure while riding. Features Adjustment strap at wrist
- The hook-&-loop adjustment strap at the wrist allows for optimum adjustability & fit when using our gloves. Find the ideal tightness & comfort every time it is used. Adjustment tab at cuff Stretch lips at fingers Long cuff Hook-&-loop closure Grip patch at palm
- A grip patch is made with a texturized pattern to deliver a superb grip performance. Outside stitching
- The PWR yarn stitching is positioned on the outside of the glove, eliminating any potential pressure points at the seams, & giving these gloves the ultimate sensitivity every racer demands. Ventilation holes These gloves are certified according to the EN 13594 Standard, published in 2015 & have achieved level 1 KP rating. Outer garment 3D air mesh
- This knitted fabric has an open, 3-dimensional structure that ensures good ventilation while riding. 3D air mesh is a must-have for long touring riders. Cowhide
- Cowhide has been used in this garment for optimal fit & protection. Goatskin
- Tanned leather made from goatskin is considered extremely durable, & is often used for gloves & other products that require a soft hide. Perforated PU coated fabric PU (polyurethane) coated fabric Lining Tri-fleece liner
- This polyester tricot fabric is used for glove lining, & brushed to provide extra warmth without adding any bulk. The lining wicks moisture away, to prevent hands from getting damp. Protection Outseam stitching by Guterman
- Marketing calls it PWR yarn Temperfoam® finger knuckles
- The self-contouring foam is used in areas where mobility & fit are a must, like the finger knuckles. Temperfoam® comes in a solid version as well as a perforated version. TPU hard shell finger knuckles
- Thermoplastic Urethane (TPU) is a highly durable synthetic material, used in many REV’IT! products for protection & waterproofing. TPU hard shell knuckle TPU hard shell little finger protector TPU hard shell palm slider
- Palm slider made from a durable & high abrasion resistant TPU material at the palm side of the glove. The palm slider makes sure that the glove slides in case the palm of the hand comes in contact with the asphalt. The abrasion resistance of gloves equipped with these sliders is greatly increased, thus reducing the risk of injury significantly. TPU hard shell thumb protector TPU cuff protector
- We use Thermoplastic Urethane (TPU)
- a highly durable synthetic material – at the cuff of these gloves to add additional impact protection & to optimize sliding in the event of a mishap. Ventilated dual comp protector
- The dual-comp protector consists of a 3D, pre-shaped honeycomb structure of TPU material, topped by an aluminum high-impact shield, for ultimate sliding. This lightweight hard part increases the level of protection significantly, without adding the considerable weight of traditional plastic hard parts. The dual comp protectors have been perforated to allow airflow to enter the gloves keeping your hands cool & comfortable.













...

Engineered to perform, built to last & to protect, the long-cuffed Quantum 2 gloves have been designed to look great with any one-piece suits or sport jackets in the REV IT! Quantum collection. Race-spec knuckles, finger, palm, & cuff protection & sliders, are just a few incorporated features. Supple yet strong drum dyed goatskin & cowhide leather & stretch panels protect hands & allow for freedom of movement. An adjustment strap at the wrist & an adjustment tab at the cuff ensure the Quantum 2 gloves stay secure while riding. Features Adjustment strap at wrist
- The hook-&-loop adjustment strap at the wrist allows for optimum adjustability & fit when using our gloves. Find the ideal tightness & comfort every time it is used. Adjustment tab at cuff Stretch lips at fingers Long cuff Hook-&-loop closure Grip patch at palm
- A grip patch is made with a texturized pattern to deliver a superb grip performance. Outside stitching
- The PWR yarn stitching is positioned on the outside of the glove, eliminating any potential pressure points at the seams, & giving these gloves the ultimate sensitivity every racer demands. Ventilation holes These gloves are certified according to the EN 13594 Standard, published in 2015 & have achieved level 1 KP rating. Outer garment 3D air mesh
- This knitted fabric has an open, 3-dimensional structure that ensures good ventilation while riding. 3D air mesh is a must-have for long touring riders. Cowhide
- Cowhide has been used in this garment for optimal fit & protection. Goatskin
- Tanned leather made from goatskin is considered extremely durable, & is often used for gloves & other products that require a soft hide. Perforated PU coated fabric PU (polyurethane) coated fabric Lining Tri-fleece liner
- This polyester tricot fabric is used for glove lining, & brushed to provide extra warmth without adding any bulk. The lining wicks moisture away, to prevent hands from getting damp. Protection Outseam stitching by Guterman
- Marketing calls it PWR yarn Temperfoam® finger knuckles
- The self-contouring foam is used in areas where mobility & fit are a must, like the finger knuckles. Temperfoam® comes in a solid version as well as a perforated version. TPU hard shell finger knuckles
- Thermoplastic Urethane (TPU) is a highly durable synthetic material, used in many REV’IT! products for protection & waterproofing. TPU hard shell knuckle TPU hard shell little finger protector TPU hard shell palm slider
- Palm slider made from a durable & high abrasion resistant TPU material at the palm side of the glove. The palm slider makes sure that the glove slides in case the palm of the hand comes in contact with the asphalt. The abrasion resistance of gloves equipped with these sliders is greatly increased, thus reducing the risk of injury significantly. TPU hard shell thumb protector TPU cuff protector
- We use Thermoplastic Urethane (TPU)
- a highly durable synthetic material – at the cuff of these gloves to add additional impact protection & to optimize sliding in the event of a mishap. Ventilated dual comp protector
- The dual-comp protector consists of a 3D, pre-shaped honeycomb structure of TPU material, topped by an aluminum high-impact shield, for ultimate sliding. This lightweight hard part increases the level of protection significantly, without adding the considerable weight of traditional plastic hard parts. The dual comp protectors have been perforated to allow airflow to enter the gloves keeping your hands cool & comfortable.













...

Engineered to perform, built to last & to protect, the long-cuffed Quantum 2 gloves have been designed to look great with any one-piece suits or sport jackets in the REV IT! Quantum collection. Race-spec knuckles, finger, palm, & cuff protection & sliders, are just a few incorporated features. Supple yet strong drum dyed goatskin & cowhide leather & stretch panels protect hands & allow for freedom of movement. An adjustment strap at the wrist & an adjustment tab at the cuff ensure the Quantum 2 gloves stay secure while riding. Features Adjustment strap at wrist
- The hook-&-loop adjustment strap at the wrist allows for optimum adjustability & fit when using our gloves. Find the ideal tightness & comfort every time it is used. Adjustment tab at cuff Stretch lips at fingers Long cuff Hook-&-loop closure Grip patch at palm
- A grip patch is made with a texturized pattern to deliver a superb grip performance. Outside stitching
- The PWR yarn stitching is positioned on the outside of the glove, eliminating any potential pressure points at the seams, & giving these gloves the ultimate sensitivity every racer demands. Ventilation holes These gloves are certified according to the EN 13594 Standard, published in 2015 & have achieved level 1 KP rating. Outer garment 3D air mesh
- This knitted fabric has an open, 3-dimensional structure that ensures good ventilation while riding. 3D air mesh is a must-have for long touring riders. Cowhide
- Cowhide has been used in this garment for optimal fit & protection. Goatskin
- Tanned leather made from goatskin is considered extremely durable, & is often used for gloves & other products that require a soft hide. Perforated PU coated fabric PU (polyurethane) coated fabric Lining Tri-fleece liner
- This polyester tricot fabric is used for glove lining, & brushed to provide extra warmth without adding any bulk. The lining wicks moisture away, to prevent hands from getting damp. Protection Outseam stitching by Guterman
- Marketing calls it PWR yarn Temperfoam® finger knuckles
- The self-contouring foam is used in areas where mobility & fit are a must, like the finger knuckles. Temperfoam® comes in a solid version as well as a perforated version. TPU hard shell finger knuckles
- Thermoplastic Urethane (TPU) is a highly durable synthetic material, used in many REV’IT! products for protection & waterproofing. TPU hard shell knuckle TPU hard shell little finger protector TPU hard shell palm slider
- Palm slider made from a durable & high abrasion resistant TPU material at the palm side of the glove. The palm slider makes sure that the glove slides in case the palm of the hand comes in contact with the asphalt. The abrasion resistance of gloves equipped with these sliders is greatly increased, thus reducing the risk of injury significantly. TPU hard shell thumb protector TPU cuff protector
- We use Thermoplastic Urethane (TPU)
- a highly durable synthetic material – at the cuff of these gloves to add additional impact protection & to optimize sliding in the event of a mishap. Ventilated dual comp protector
- The dual-comp protector consists of a 3D, pre-shaped honeycomb structure of TPU material, topped by an aluminum high-impact shield, for ultimate sliding. This lightweight hard part increases the level of protection significantly, without adding the considerable weight of traditional plastic hard parts. The dual comp protectors have been perforated to allow airflow to enter the gloves keeping your hands cool & comfortable.













...

Engineered to perform, built to last & to protect, the long-cuffed Quantum 2 gloves have been designed to look great with any one-piece suits or sport jackets in the REV IT! Quantum collection. Race-spec knuckles, finger, palm, & cuff protection & sliders, are just a few incorporated features. Supple yet strong drum dyed goatskin & cowhide leather & stretch panels protect hands & allow for freedom of movement. An adjustment strap at the wrist & an adjustment tab at the cuff ensure the Quantum 2 gloves stay secure while riding. Features Adjustment strap at wrist
- The hook-&-loop adjustment strap at the wrist allows for optimum adjustability & fit when using our gloves. Find the ideal tightness & comfort every time it is used. Adjustment tab at cuff Stretch lips at fingers Long cuff Hook-&-loop closure Grip patch at palm
- A grip patch is made with a texturized pattern to deliver a superb grip performance. Outside stitching
- The PWR yarn stitching is positioned on the outside of the glove, eliminating any potential pressure points at the seams, & giving these gloves the ultimate sensitivity every racer demands. Ventilation holes These gloves are certified according to the EN 13594 Standard, published in 2015 & have achieved level 1 KP rating. Outer garment 3D air mesh
- This knitted fabric has an open, 3-dimensional structure that ensures good ventilation while riding. 3D air mesh is a must-have for long touring riders. Cowhide
- Cowhide has been used in this garment for optimal fit & protection. Goatskin
- Tanned leather made from goatskin is considered extremely durable, & is often used for gloves & other products that require a soft hide. Perforated PU coated fabric PU (polyurethane) coated fabric Lining Tri-fleece liner
- This polyester tricot fabric is used for glove lining, & brushed to provide extra warmth without adding any bulk. The lining wicks moisture away, to prevent hands from getting damp. Protection Outseam stitching by Guterman
- Marketing calls it PWR yarn Temperfoam® finger knuckles
- The self-contouring foam is used in areas where mobility & fit are a must, like the finger knuckles. Temperfoam® comes in a solid version as well as a perforated version. TPU hard shell finger knuckles
- Thermoplastic Urethane (TPU) is a highly durable synthetic material, used in many REV’IT! products for protection & waterproofing. TPU hard shell knuckle TPU hard shell little finger protector TPU hard shell palm slider
- Palm slider made from a durable & high abrasion resistant TPU material at the palm side of the glove. The palm slider makes sure that the glove slides in case the palm of the hand comes in contact with the asphalt. The abrasion resistance of gloves equipped with these sliders is greatly increased, thus reducing the risk of injury significantly. TPU hard shell thumb protector TPU cuff protector
- We use Thermoplastic Urethane (TPU)
- a highly durable synthetic material – at the cuff of these gloves to add additional impact protection & to optimize sliding in the event of a mishap. Ventilated dual comp protector
- The dual-comp protector consists of a 3D, pre-shaped honeycomb structure of TPU material, topped by an aluminum high-impact shield, for ultimate sliding. This lightweight hard part increases the level of protection significantly, without adding the considerable weight of traditional plastic hard parts. The dual comp protectors have been perforated to allow airflow to enter the gloves keeping your hands cool & comfortable.













...