To correct the flashing frequency of the indicator light when using Kellermann LED turn signals with original LED turn signals (12V)
-
...

When converting the original turn signals, the flashing frequency may increase. Load-independent flasher relays (e.g. R2) or multifunctional assistance systems (e.g. CR4®) can provide a remedy. If this use is not possible or desired, power resistors connected in parallel can provide a remedy. On motorcycle models with an illumination indicator lamp in addition to the indicator lamp (especially older BMWs), this indicator lamp may be displayed incorrectly when the DF combinations are used. In this case, a resistor of 33 ohms in parallel to the tail light & a resistor of 7.5 ohms in parallel to the brake light is required. ...

Power resistor for use with Kellermann LED turn signals with original 10 watt turn signals
- 1 pc. per turn signal required. When
...

When converting the original turn signals, the flashing frequency may increase. Load-independent flasher relays (e.g. R2) or multifunctional assistance systems (e.g. CR4®) can provide a remedy. If this use is not possible or desired, power resistors connected in parallel can provide a remedy. On motorcycle models with an illumination indicator lamp in addition to the indicator lamp (especially older BMWs), this indicator lamp may be displayed incorrectly when the DF combinations are used. In this case, a resistor of 33 ohms in parallel to the tail light & a resistor of 7.5 ohms in parallel to the brake light is required. ...

Kellermann i.SED V6 & i.SED V12, electronic flasher relays. Suitable e.g. for mounting of turn signals with higher power than original of turn signals with higher voltage than original of turn signals to vehicles with plus (+) to ground (-) Features i.SED V6 for on-board voltage 3
- 9 Volt i.SED V12 for on-board voltage 12 Volt
...

The Kellermann Jetstream® is probably the most spectacular motorcycle turn signal of all time. The shape is extremely aerodynamic & therefore particularly streamlined even at higher speeds. No other motorcycle running light flasher with ECE approval has so far achieved the luminosity of the Kellermann Jetstream®. In the combined DF version, the equally dark luminous tail & brake lights are added, in which the proven focused Atto® lighting technology is used in the engine ducts. ECE-approved for front & rear Highest light output Kellermann High Power LED Technology most modern "IC" chip technology 32 MHz real-time microprocessor control Silent-Current, advanced Power Saving Algorithm High level of visibility over a wide angular range Longlife Protection Guard® Suitable for 12 volt DC power supplies Flow-optimized metal housing, highest quality workmanship M8 x 20 mm thread High-quality silent bearing, vibration-absorbing mounting element Globally protected design Features Functiona... ...

The Kellermann Jetstream® is probably the most spectacular motorcycle turn signal of all time. The shape is extremely aerodynamic & therefore particularly streamlined even at higher speeds. No other motorcycle running light turn signal with ECE approval has so far achieved the luminosity of the Kellermann Jetstream®. This makes overtaking safer, as a vehicle in front is warned more clearly by the extreme luminosity during the flashing process, thus reducing the risk of accidentally changing lanes. ECE-approved for front & rear Highest light output Kellermann High Power LED Technology most modern "IC" chip technology 32 MHz real-time microprocessor control Silent-Current, advanced Power Saving Algorithm High level of visibility over a wide angular range Longlife Protection Guard® Suitable for 12 volt DC power supplies Flow-optimized metal housing, highest quality workmanship M8 x 20 mm thread High-quality silent bearing, vibration-absorbing mounting element Globally protected design... ...

Decent, slim reflector for the rear. Features

Dimensions 100 x 13 mm Mounting with 5 mm threaded bolt ...

The license plate light KL 1 is a small sensation on every motorcycle due to its micro construction & unique design. Through specially developed optics, the license plate is illuminated completely pure white (CRI >80). No light is emitted in the direction of following traffic. The KL 1 in the high-quality metal housing can be mounted with its holder by means of enclosed mounting strips on the license plate holder or directly on the license plate. Instead of the enclosed holder can also be used own holders, which have a tab with the

Dimensions Lx Wx H 6 x 7 x 3 cm. Suitable for all motorcycle types. ECE approved Micro design Pure white light (CRI >80 according to CRI
- color rendering index) High quality metal housing Suitable for 12 volt DC electrical systems Features Attachment: Surface-mount article

Width: 79 mm ECE approval: Motorcycles DC power supply: 12V

Height: 75 mm length (without thread/fixing): 113 mm Lens
Colour: clear







...

Upgrade set for the Kellermann KTW 2.0 chain tool to the newer version KTW 2.5. Content Mandrel 4xx Mandrel 5xx & 6xx Guide Fixing screw Pressure screw ...