The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license plates. To allow the installation of the turn signals without separation from the wiring harness, the 10 mm holes are slotted to the side. You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of EU license plates is therefore no problem. To screw the license plate securely & reduce vibrations, two rubber washers are included. Another rubber buffer supports the license plate on its underside. Features Model specific mount Continuously adjustable turn signal holder Slotted turn signal mount for easy installation without cable separation Continuously adjustable reflector, E-approved Suitable for European license plates Steplessly adjustable tilt angle Additional screw for optimal position security Easy fixation without further work steps (e.g. drilling) Easy mounting of the license plate through slotted holes The scope of delivery of the HIGHSIDER Akron-RS

Includes:: Model-specific bracket with mounting parts HIGHSIDER Akron-RS license plate mounting plate Adjustable turn signal brackets E-tested reflector with adjustable bracket Mounting instructions Notes If there are side reflectors mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones. For the original turn signals the special turn signal holder 280-970 is optionally available.

...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license... ...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license... ...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license... ...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license plates. To allow the installation of the turn signals without separation from the wiring harness, the 10 mm holes are slotted to the side. You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of EU license plates is therefore no problem. To screw the license plate securely & reduce vibrations, two rubber washers are included. Another rubber buffer supports the license plate on its underside. Features Model specific mount Continuously adjustable turn signal holder Slotted turn signal mount for easy installation without cable separation Continuously adjustable reflector, E-approved Suitable for European license plates Steplessly adjustable tilt angle Additional screw for optimal position security Easy fixation without further work steps (e.g. drilling) Easy mounting of the license plate through slotted holes The scope of delivery of the HIGHSIDER Akron-RS

Includes:: Model-specific bracket with mounting parts HIGHSIDER Akron-RS license plate mounting plate Adjustable turn signal brackets E-tested reflector with adjustable bracket Mounting instructions Notes If there are side reflectors mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones. For the original turn signals the special turn signal holder 280-970 is optionally available.

...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license plates. To allow the installation of the turn signals without separation from the wiring harness, the 10 mm holes are slotted to the side. You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of EU license plates is therefore no problem. To screw the license plate securely & reduce vibrations, two rubber washers are included. Another rubber buffer supports the license plate on its underside. Features Model specific mount Continuously adjustable turn signal holder Slotted turn signal mount for easy installation without cable separation Continuously adjustable reflector, E-approved Suitable for European license plates Steplessly adjustable tilt angle Additional screw for optimal position security Easy fixation without further work steps (e.g. drilling) Easy mounting of the license plate through slotted holes The scope of delivery of the HIGHSIDER Akron-RS

Includes:: Model-specific bracket with mounting parts HIGHSIDER Akron-RS license plate mounting plate Adjustable turn signal brackets E-tested reflector with adjustable bracket Mounting instructions Notes If there are side reflectors mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones. For the original turn signals the special turn signal holder 280-970 is optionally available.

...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license... ...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license... ...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license... ...

The HIGHSIDER Akron-RS license plate holder adapts perfectly to the lines of your bike through its design. The model-specific bracket of the HIGHSIDER Akron-RS allows mounting on the original mounting points of your bike & thus a replacement without further drilling or cutting. To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet. The license plate is made from sheet steel & 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating. This ensures an optimal fit & durability. The stepless adjustment means that you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw. The turn signal mounts of the HIGHSIDER Akron-RS are adjustable in width & thus suitable for any type of accessory turn signals. Through this adjustment option, you can adjust the position of your turn signals to the most diverse license... ...