The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation...
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation...
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation...
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation...
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation...
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation Exhaust vent at the neck Side exhaust vents Aerodynamics Pull-down chin spoiler Patented Air Wing® adjustable (innovative & offered exclusively by Arai) Visor VAS Max Vision visor with anti-fog option New locking lever for the visor Pinlock lens included Inner lining Antimicrobial material Replaceable cheek pads Replaceable inner liner Replaceable chinstrap covers Replaceable neck roll Speaker pockets Face Contour System (FCS) 5 mm Peel Away cheek pads 5 mm Peel Away temple padding Thin center pad for more space in the front area Comfort Emergency Release System (ERS) Breathing protection Chin wind deflector Homologation ECE 22-06 SNELL M2010/2015 RX-7V Ventilation New diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Shell Construction: PB-SNC2 Peripherally Belted Structural Net Composite Arai´s proprietary (super fibre belt) Peripheral Belt, borrowed from our F-1 technology, maximizes shell strength & flexibility while maintaining low weight. Positioned across the top of the eye port, this band allows the use of a thinner EPS liner which greatly enhances the upward field of view – especially appreciated in a full racing tuck! The Structural Net Composite adds a physical bond to the resin bond of the many layers of fibres & reinforcing materials within the shell. Variable Axis System (VAS) With VAS, the visor mounting position is lowered, yielding an average of an additional 24mm across both temple areas, in pursuit of the ideal smoother shape that increases the ability of glancing off energy. As a result, this has made it possible for more of the shell to be smoother along & above the test line of the Snell standard. Ventilation: Free Flow System (FFS) Creates airflow under the helmet that reduces wind noise & turbulence while increasing the exhaust of hot air. Ventilation: Eyeport Airchannel Enhanced air exhaust from the eye port area, pulled through dedicated air channel to side ducts, improving efficiency & reducing noise. Front Ventilation: Center top vent The new Top Vent provides 11% more airflow than the previous Vent. The new bigger switch makes opening & closing easier. The new Top Vent has three positions, closed, half open & fully open to adjust the airflow & prevent water intrusion when fully closed. Front Ventilation: Diffuser system The new diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Front Ventilation: Brow vents extended to temple area Fresh air can enter directly to the forehead area without the need for holes in this critical area of the shell & impact absorbing liner. For specific models the ventilation is extended to the temple area. Rear Ventilation: Neck exhaust vent To enhance hot-air extraction from the interior. Increases the ventilation effect at the lower part of the helmet. Rear Ventilation: Side exhausts Produce low pressure behind the rear vent for better hot air extraction. Integrated in the shell for better aerodynamics, reduce wind noise & prevent buffeting at speed. Inside, a small foam dam helps to absorb & diminish excessive noise, without reducing ventilation performance. Aerodynamics: Pull Down Chin Spoiler Helps minimize wind noise & also aids with the extraction of hot air from the face area. Provides additional deflection of road debris away from neck. Depending on the model the Chin Spoiler is retractable. Aerodynamics: Patented Air Wing® adjustable Moto GP tested & designed to greatly reduce drag, turbulence & buffeting resulting in more comfort & additional top-speed. It improves stability of the helmet at high speeds or when braking hard & reduces noise. Depending on the model the Air Wing is adjustable in five different angles of attack positions to suit every riding position. Visor: VAS Max Vision Visor with De-Mist option VAS MAX Vision shield is standard to provide better visibility in all seasons & for all types of riding. Comes standard with Clear anti-fog Pinlock insert to be installed as needed. Visor: Pinlock insert lens included Effectively prevents misting & fogging of the visor, even under extreme wet & damp conditions. May be cleaned & changed easily. Interior: Antimicrobial Liner New exclusive liner with antimicrobial stays fresher between cleanings. Interior: Replaceable Interior Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Replaceable Neckroll Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Facial Contour System (FCS) To offer an even better snug fit & enhancing the comfort to the lower jaw, the Facial Contour System (FCS) works with a foam spring support in the cheek pad that compresses & rebounds, providing the necessary support without excessive pressure. Interior: 5mm ’’ Peel Away’’ Ear cups/ Cheek pads Giving even more ability to craft the perfect fit & comfort, the cheek pads now feature a 5 mm peel away layer for added room if needed. Interior: 5mm ’’ Peel Away’’ Temple pad Arai´s peel-away temple crown pads give the option of 5 mm more interior with* if needed. Comfort: Emergency Release System (ERS) Allows easier access to an injured rider. By pulling the orange tabs integrated in the pads, the cheek pads slide out. Making helmet removal easier for trained medical personnel & rescuers. Minimising the risk of additional injury. Comfort: Breath guard Works in conjunction with the dual-pivot® chin vent to better direct fresh air to the inside surface of the shield while at the same time directing hot breath down & away from the inside surface of the shield. Comfort: Chin Curtain Attached to the bottom of the helmet, the new chin curtain helps to further accentuate the Egg-shape form. The curtain simultaneously blocks air intrusion from turbulent air below & increases negative pressure to enhance the exhaust function of FFS by drawing more air from the mouth area. The enhanced airflow reduces noise even further. Approval: ECE 22-06 The most widely used & required international helmet testing standard. This helmet is approved according to the latest version of the testing standard ECE 22-06. This is valid in more than 50 countries. Approval: SNELL M2010/2015 The American SNELL Memorial Foundation is an independent organisation, SNELL M2010 is their latest new, more shock-absorbent standard. For the M2010 standard a steel ball shaped rather like a tennis ball anvil is used, they also test with flat & “kerb” shaped anvils). The impact test area of SNELL is larger than that of ECE. Multiple impacts & a penetration test on random spots are used. Five times inspected Each Arai helmet goes through five separate quality-control depart­ments: after the shell is made, after painting & graphic completion, after assembly & two in-process inspections. Washable interior The premium quality interior of any Arai helmet can be easily cleaned, in place, with mild soap & lukewarm water. Handmade It can take up to five years for our experts to earn the right to create an Arai shell. Each shell can take up to 27 steps & to build one Arai helmet will take about 18 man-hours. All-day comfort All-day comfort with the Arai interior fit & shape together with the finest liner materials & the extensive ventilation system. & thanks to the perfect balance & weight distribution of the helmet, you hardly notice you are wearing an Arai. Penetration tested All Arai helmets are penetration tested, although not required by European helmet standards. The Arai penetration test is performed with a 3kg test cone that strikes from a height of 3m on the helmet. Double-D ring closure The flat & D-shaped rings fit smooth against the chin. No moving parts, no corrosion problems & just pulling the tab is enough to loosen the fastener. Smooth shape, better protection The smooth outer shell of Arai helmets is designed to glide without unnecessary resistance. You don’t want to decelerate your helmet more than necessary. That’s why all Arai vents & ducts are designed to break off during an impact. Hard outer shell, soft inner shell Arai uses a very hard outer shell to spread impact forces & a soft inner shell to absorb remaining energy. The multiple-density EPS inner shell is made using a unique technology of combining three to five densities in various areas as a single component. 5-year limited warranty All Arai helmets are warranted against defects in materials & workmanship, & are serviceable only for the properly fitted first user for 5 years from date of first use, but no more than 7 years from date of manufacture. Arai In-house test This Arai helmet is designed to meet the stringent Arai In-house standard requirements, in addition to mandatory standards such as ECE 22-05 & voluntary standards such as SNELL M2010. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default all helmets that have a visor will be delivered with a clear visor, even if it is shown differently.
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation Exhaust vent at the neck Side exhaust vents Aerodynamics Pull-down chin spoiler Patented Air Wing® adjustable (innovative & offered exclusively by Arai) Visor VAS Max Vision visor with anti-fog option New locking lever for the visor Pinlock lens included Inner lining Antimicrobial material Replaceable cheek pads Replaceable inner liner Replaceable chinstrap covers Replaceable neck roll Speaker pockets Face Contour System (FCS) 5 mm Peel Away cheek pads 5 mm Peel Away temple padding Thin center pad for more space in the front area Comfort Emergency Release System (ERS) Breathing protection Chin wind deflector Homologation ECE 22-06 SNELL M2010/2015 RX-7V Ventilation New diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Shell Construction: PB-SNC2 Peripherally Belted Structural Net Composite Arai´s proprietary (super fibre belt) Peripheral Belt, borrowed from our F-1 technology, maximizes shell strength & flexibility while maintaining low weight. Positioned across the top of the eye port, this band allows the use of a thinner EPS liner which greatly enhances the upward field of view – especially appreciated in a full racing tuck! The Structural Net Composite adds a physical bond to the resin bond of the many layers of fibres & reinforcing materials within the shell. Variable Axis System (VAS) With VAS, the visor mounting position is lowered, yielding an average of an additional 24mm across both temple areas, in pursuit of the ideal smoother shape that increases the ability of glancing off energy. As a result, this has made it possible for more of the shell to be smoother along & above the test line of the Snell standard. Ventilation: Free Flow System (FFS) Creates airflow under the helmet that reduces wind noise & turbulence while increasing the exhaust of hot air. Ventilation: Eyeport Airchannel Enhanced air exhaust from the eye port area, pulled through dedicated air channel to side ducts, improving efficiency & reducing noise. Front Ventilation: Center top vent The new Top Vent provides 11% more airflow than the previous Vent. The new bigger switch makes opening & closing easier. The new Top Vent has three positions, closed, half open & fully open to adjust the airflow & prevent water intrusion when fully closed. Front Ventilation: Diffuser system The new diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Front Ventilation: Brow vents extended to temple area Fresh air can enter directly to the forehead area without the need for holes in this critical area of the shell & impact absorbing liner. For specific models the ventilation is extended to the temple area. Rear Ventilation: Neck exhaust vent To enhance hot-air extraction from the interior. Increases the ventilation effect at the lower part of the helmet. Rear Ventilation: Side exhausts Produce low pressure behind the rear vent for better hot air extraction. Integrated in the shell for better aerodynamics, reduce wind noise & prevent buffeting at speed. Inside, a small foam dam helps to absorb & diminish excessive noise, without reducing ventilation performance. Aerodynamics: Pull Down Chin Spoiler Helps minimize wind noise & also aids with the extraction of hot air from the face area. Provides additional deflection of road debris away from neck. Depending on the model the Chin Spoiler is retractable. Aerodynamics: Patented Air Wing® adjustable Moto GP tested & designed to greatly reduce drag, turbulence & buffeting resulting in more comfort & additional top-speed. It improves stability of the helmet at high speeds or when braking hard & reduces noise. Depending on the model the Air Wing is adjustable in five different angles of attack positions to suit every riding position. Visor: VAS Max Vision Visor with De-Mist option VAS MAX Vision shield is standard to provide better visibility in all seasons & for all types of riding. Comes standard with Clear anti-fog Pinlock insert to be installed as needed. Visor: Pinlock insert lens included Effectively prevents misting & fogging of the visor, even under extreme wet & damp conditions. May be cleaned & changed easily. Interior: Antimicrobial Liner New exclusive liner with antimicrobial stays fresher between cleanings. Interior: Replaceable Interior Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Replaceable Neckroll Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Facial Contour System (FCS) To offer an even better snug fit & enhancing the comfort to the lower jaw, the Facial Contour System (FCS) works with a foam spring support in the cheek pad that compresses & rebounds, providing the necessary support without excessive pressure. Interior: 5mm ’’ Peel Away’’ Ear cups/ Cheek pads Giving even more ability to craft the perfect fit & comfort, the cheek pads now feature a 5 mm peel away layer for added room if needed. Interior: 5mm ’’ Peel Away’’ Temple pad Arai´s peel-away temple crown pads give the option of 5 mm more interior with* if needed. Comfort: Emergency Release System (ERS) Allows easier access to an injured rider. By pulling the orange tabs integrated in the pads, the cheek pads slide out. Making helmet removal easier for trained medical personnel & rescuers. Minimising the risk of additional injury. Comfort: Breath guard Works in conjunction with the dual-pivot® chin vent to better direct fresh air to the inside surface of the shield while at the same time directing hot breath down & away from the inside surface of the shield. Comfort: Chin Curtain Attached to the bottom of the helmet, the new chin curtain helps to further accentuate the Egg-shape form. The curtain simultaneously blocks air intrusion from turbulent air below & increases negative pressure to enhance the exhaust function of FFS by drawing more air from the mouth area. The enhanced airflow reduces noise even further. Approval: ECE 22-06 The most widely used & required international helmet testing standard. This helmet is approved according to the latest version of the testing standard ECE 22-06. This is valid in more than 50 countries. Approval: SNELL M2010/2015 The American SNELL Memorial Foundation is an independent organisation, SNELL M2010 is their latest new, more shock-absorbent standard. For the M2010 standard a steel ball shaped rather like a tennis ball anvil is used, they also test with flat & “kerb” shaped anvils). The impact test area of SNELL is larger than that of ECE. Multiple impacts & a penetration test on random spots are used. Five times inspected Each Arai helmet goes through five separate quality-control depart­ments: after the shell is made, after painting & graphic completion, after assembly & two in-process inspections. Washable interior The premium quality interior of any Arai helmet can be easily cleaned, in place, with mild soap & lukewarm water. Handmade It can take up to five years for our experts to earn the right to create an Arai shell. Each shell can take up to 27 steps & to build one Arai helmet will take about 18 man-hours. All-day comfort All-day comfort with the Arai interior fit & shape together with the finest liner materials & the extensive ventilation system. & thanks to the perfect balance & weight distribution of the helmet, you hardly notice you are wearing an Arai. Penetration tested All Arai helmets are penetration tested, although not required by European helmet standards. The Arai penetration test is performed with a 3kg test cone that strikes from a height of 3m on the helmet. Double-D ring closure The flat & D-shaped rings fit smooth against the chin. No moving parts, no corrosion problems & just pulling the tab is enough to loosen the fastener. Smooth shape, better protection The smooth outer shell of Arai helmets is designed to glide without unnecessary resistance. You don’t want to decelerate your helmet more than necessary. That’s why all Arai vents & ducts are designed to break off during an impact. Hard outer shell, soft inner shell Arai uses a very hard outer shell to spread impact forces & a soft inner shell to absorb remaining energy. The multiple-density EPS inner shell is made using a unique technology of combining three to five densities in various areas as a single component. 5-year limited warranty All Arai helmets are warranted against defects in materials & workmanship, & are serviceable only for the properly fitted first user for 5 years from date of first use, but no more than 7 years from date of manufacture. Arai In-house test This Arai helmet is designed to meet the stringent Arai In-house standard requirements, in addition to mandatory standards such as ECE 22-05 & voluntary standards such as SNELL M2010. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default, even if it is shown differently. all helmets that have a visor will be delivered with a clear visor, even if it is shown differently.
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation Exhaust vent at the neck Side exhaust vents Aerodynamics Pull-down chin spoiler Patented Air Wing® adjustable (innovative & offered exclusively by Arai) Visor VAS Max Vision visor with anti-fog option New locking lever for the visor Pinlock lens included Inner lining Antimicrobial material Replaceable cheek pads Replaceable inner liner Replaceable chinstrap covers Replaceable neck roll Speaker pockets Face Contour System (FCS) 5 mm Peel Away cheek pads 5 mm Peel Away temple padding Thin center pad for more space in the front area Comfort Emergency Release System (ERS) Breathing protection Chin wind deflector Homologation ECE 22-06 SNELL M2010/2015 RX-7V Ventilation New diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Shell Construction: PB-SNC2 Peripherally Belted Structural Net Composite Arai´s proprietary (super fibre belt) Peripheral Belt, borrowed from our F-1 technology, maximizes shell strength & flexibility while maintaining low weight. Positioned across the top of the eye port, this band allows the use of a thinner EPS liner which greatly enhances the upward field of view – especially appreciated in a full racing tuck! The Structural Net Composite adds a physical bond to the resin bond of the many layers of fibres & reinforcing materials within the shell. Variable Axis System (VAS) With VAS, the visor mounting position is lowered, yielding an average of an additional 24mm across both temple areas, in pursuit of the ideal smoother shape that increases the ability of glancing off energy. As a result, this has made it possible for more of the shell to be smoother along & above the test line of the Snell standard. Ventilation: Free Flow System (FFS) Creates airflow under the helmet that reduces wind noise & turbulence while increasing the exhaust of hot air. Ventilation: Eyeport Airchannel Enhanced air exhaust from the eye port area, pulled through dedicated air channel to side ducts, improving efficiency & reducing noise. Front Ventilation: Center top vent The new Top Vent provides 11% more airflow than the previous Vent. The new bigger switch makes opening & closing easier. The new Top Vent has three positions, closed, half open & fully open to adjust the airflow & prevent water intrusion when fully closed. Front Ventilation: Diffuser system The new diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Front Ventilation: Brow vents extended to temple area Fresh air can enter directly to the forehead area without the need for holes in this critical area of the shell & impact absorbing liner. For specific models the ventilation is extended to the temple area. Rear Ventilation: Neck exhaust vent To enhance hot-air extraction from the interior. Increases the ventilation effect at the lower part of the helmet. Rear Ventilation: Side exhausts Produce low pressure behind the rear vent for better hot air extraction. Integrated in the shell for better aerodynamics, reduce wind noise & prevent buffeting at speed. Inside, a small foam dam helps to absorb & diminish excessive noise, without reducing ventilation performance. Aerodynamics: Pull Down Chin Spoiler Helps minimize wind noise & also aids with the extraction of hot air from the face area. Provides additional deflection of road debris away from neck. Depending on the model the Chin Spoiler is retractable. Aerodynamics: Patented Air Wing® adjustable Moto GP tested & designed to greatly reduce drag, turbulence & buffeting resulting in more comfort & additional top-speed. It improves stability of the helmet at high speeds or when braking hard & reduces noise. Depending on the model the Air Wing is adjustable in five different angles of attack positions to suit every riding position. Visor: VAS Max Vision Visor with De-Mist option VAS MAX Vision shield is standard to provide better visibility in all seasons & for all types of riding. Comes standard with Clear anti-fog Pinlock insert to be installed as needed. Visor: Pinlock insert lens included Effectively prevents misting & fogging of the visor, even under extreme wet & damp conditions. May be cleaned & changed easily. Interior: Antimicrobial Liner New exclusive liner with antimicrobial stays fresher between cleanings. Interior: Replaceable Interior Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Replaceable Neckroll Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Facial Contour System (FCS) To offer an even better snug fit & enhancing the comfort to the lower jaw, the Facial Contour System (FCS) works with a foam spring support in the cheek pad that compresses & rebounds, providing the necessary support without excessive pressure. Interior: 5mm ’’ Peel Away’’ Ear cups/ Cheek pads Giving even more ability to craft the perfect fit & comfort, the cheek pads now feature a 5 mm peel away layer for added room if needed. Interior: 5mm ’’ Peel Away’’ Temple pad Arai´s peel-away temple crown pads give the option of 5 mm more interior with* if needed. Comfort: Emergency Release System (ERS) Allows easier access to an injured rider. By pulling the orange tabs integrated in the pads, the cheek pads slide out. Making helmet removal easier for trained medical personnel & rescuers. Minimising the risk of additional injury. Comfort: Breath guard Works in conjunction with the dual-pivot® chin vent to better direct fresh air to the inside surface of the shield while at the same time directing hot breath down & away from the inside surface of the shield. Comfort: Chin Curtain Attached to the bottom of the helmet, the new chin curtain helps to further accentuate the Egg-shape form. The curtain simultaneously blocks air intrusion from turbulent air below & increases negative pressure to enhance the exhaust function of FFS by drawing more air from the mouth area. The enhanced airflow reduces noise even further. Approval: ECE 22-06 The most widely used & required international helmet testing standard. This helmet is approved according to the latest version of the testing standard ECE 22-06. This is valid in more than 50 countries. Approval: SNELL M2010/2015 The American SNELL Memorial Foundation is an independent organisation, SNELL M2010 is their latest new, more shock-absorbent standard. For the M2010 standard a steel ball shaped rather like a tennis ball anvil is used, they also test with flat & “kerb” shaped anvils). The impact test area of SNELL is larger than that of ECE. Multiple impacts & a penetration test on random spots are used. Five times inspected Each Arai helmet goes through five separate quality-control depart­ments: after the shell is made, after painting & graphic completion, after assembly & two in-process inspections. Washable interior The premium quality interior of any Arai helmet can be easily cleaned, in place, with mild soap & lukewarm water. Handmade It can take up to five years for our experts to earn the right to create an Arai shell. Each shell can take up to 27 steps & to build one Arai helmet will take about 18 man-hours. All-day comfort All-day comfort with the Arai interior fit & shape together with the finest liner materials & the extensive ventilation system. & thanks to the perfect balance & weight distribution of the helmet, you hardly notice you are wearing an Arai. Penetration tested All Arai helmets are penetration tested, although not required by European helmet standards. The Arai penetration test is performed with a 3kg test cone that strikes from a height of 3m on the helmet. Double-D ring closure The flat & D-shaped rings fit smooth against the chin. No moving parts, no corrosion problems & just pulling the tab is enough to loosen the fastener. Smooth shape, better protection The smooth outer shell of Arai helmets is designed to glide without unnecessary resistance. You don’t want to decelerate your helmet more than necessary. That’s why all Arai vents & ducts are designed to break off during an impact. Hard outer shell, soft inner shell Arai uses a very hard outer shell to spread impact forces & a soft inner shell to absorb remaining energy. The multiple-density EPS inner shell is made using a unique technology of combining three to five densities in various areas as a single component. 5-year limited warranty All Arai helmets are warranted against defects in materials & workmanship, & are serviceable only for the properly fitted first user for 5 years from date of first use, but no more than 7 years from date of manufacture. Arai In-house test This Arai helmet is designed to meet the stringent Arai In-house standard requirements, in addition to mandatory standards such as ECE 22-05 & voluntary standards such as SNELL M2010. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default, even if it is shown differently. all helmets that have a visor will be delivered with a clear visor, even if it is shown differently.
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation Exhaust vent at the neck Side exhaust vents Aerodynamics Pull-down chin spoiler Patented Air Wing® adjustable (innovative & offered exclusively by Arai) Visor VAS Max Vision visor with anti-fog option New locking lever for the visor Pinlock lens included Inner lining Antimicrobial material Replaceable cheek pads Replaceable inner liner Replaceable chinstrap covers Replaceable neck roll Speaker pockets Face Contour System (FCS) 5 mm Peel Away cheek pads 5 mm Peel Away temple padding Thin center pad for more space in the front area Comfort Emergency Release System (ERS) Breathing protection Chin wind deflector Homologation ECE 22-06 SNELL M2010/2015 RX-7V Ventilation New diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Shell Construction: PB-SNC2 Peripherally Belted Structural Net Composite Arai´s proprietary (super fibre belt) Peripheral Belt, borrowed from our F-1 technology, maximizes shell strength & flexibility while maintaining low weight. Positioned across the top of the eye port, this band allows the use of a thinner EPS liner which greatly enhances the upward field of view – especially appreciated in a full racing tuck! The Structural Net Composite adds a physical bond to the resin bond of the many layers of fibres & reinforcing materials within the shell. Variable Axis System (VAS) With VAS, the visor mounting position is lowered, yielding an average of an additional 24mm across both temple areas, in pursuit of the ideal smoother shape that increases the ability of glancing off energy. As a result, this has made it possible for more of the shell to be smoother along & above the test line of the Snell standard. Ventilation: Free Flow System (FFS) Creates airflow under the helmet that reduces wind noise & turbulence while increasing the exhaust of hot air. Ventilation: Eyeport Airchannel Enhanced air exhaust from the eye port area, pulled through dedicated air channel to side ducts, improving efficiency & reducing noise. Front Ventilation: Center top vent The new Top Vent provides 11% more airflow than the previous Vent. The new bigger switch makes opening & closing easier. The new Top Vent has three positions, closed, half open & fully open to adjust the airflow & prevent water intrusion when fully closed. Front Ventilation: Diffuser system The new diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Front Ventilation: Brow vents extended to temple area Fresh air can enter directly to the forehead area without the need for holes in this critical area of the shell & impact absorbing liner. For specific models the ventilation is extended to the temple area. Rear Ventilation: Neck exhaust vent To enhance hot-air extraction from the interior. Increases the ventilation effect at the lower part of the helmet. Rear Ventilation: Side exhausts Produce low pressure behind the rear vent for better hot air extraction. Integrated in the shell for better aerodynamics, reduce wind noise & prevent buffeting at speed. Inside, a small foam dam helps to absorb & diminish excessive noise, without reducing ventilation performance. Aerodynamics: Pull Down Chin Spoiler Helps minimize wind noise & also aids with the extraction of hot air from the face area. Provides additional deflection of road debris away from neck. Depending on the model the Chin Spoiler is retractable. Aerodynamics: Patented Air Wing® adjustable Moto GP tested & designed to greatly reduce drag, turbulence & buffeting resulting in more comfort & additional top-speed. It improves stability of the helmet at high speeds or when braking hard & reduces noise. Depending on the model the Air Wing is adjustable in five different angles of attack positions to suit every riding position. Visor: VAS Max Vision Visor with De-Mist option VAS MAX Vision shield is standard to provide better visibility in all seasons & for all types of riding. Comes standard with Clear anti-fog Pinlock insert to be installed as needed. Visor: Pinlock insert lens included Effectively prevents misting & fogging of the visor, even under extreme wet & damp conditions. May be cleaned & changed easily. Interior: Antimicrobial Liner New exclusive liner with antimicrobial stays fresher between cleanings. Interior: Replaceable Interior Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Replaceable Neckroll Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Facial Contour System (FCS) To offer an even better snug fit & enhancing the comfort to the lower jaw, the Facial Contour System (FCS) works with a foam spring support in the cheek pad that compresses & rebounds, providing the necessary support without excessive pressure. Interior: 5mm ’’ Peel Away’’ Ear cups/ Cheek pads Giving even more ability to craft the perfect fit & comfort, the cheek pads now feature a 5 mm peel away layer for added room if needed. Interior: 5mm ’’ Peel Away’’ Temple pad Arai´s peel-away temple crown pads give the option of 5 mm more interior with* if needed. Comfort: Emergency Release System (ERS) Allows easier access to an injured rider. By pulling the orange tabs integrated in the pads, the cheek pads slide out. Making helmet removal easier for trained medical personnel & rescuers. Minimising the risk of additional injury. Comfort: Breath guard Works in conjunction with the dual-pivot® chin vent to better direct fresh air to the inside surface of the shield while at the same time directing hot breath down & away from the inside surface of the shield. Comfort: Chin Curtain Attached to the bottom of the helmet, the new chin curtain helps to further accentuate the Egg-shape form. The curtain simultaneously blocks air intrusion from turbulent air below & increases negative pressure to enhance the exhaust function of FFS by drawing more air from the mouth area. The enhanced airflow reduces noise even further. Approval: ECE 22-06 The most widely used & required international helmet testing standard. This helmet is approved according to the latest version of the testing standard ECE 22-06. This is valid in more than 50 countries. Approval: SNELL M2010/2015 The American SNELL Memorial Foundation is an independent organisation, SNELL M2010 is their latest new, more shock-absorbent standard. For the M2010 standard a steel ball shaped rather like a tennis ball anvil is used, they also test with flat & “kerb” shaped anvils). The impact test area of SNELL is larger than that of ECE. Multiple impacts & a penetration test on random spots are used. Five times inspected Each Arai helmet goes through five separate quality-control depart­ments: after the shell is made, after painting & graphic completion, after assembly & two in-process inspections. Washable interior The premium quality interior of any Arai helmet can be easily cleaned, in place, with mild soap & lukewarm water. Handmade It can take up to five years for our experts to earn the right to create an Arai shell. Each shell can take up to 27 steps & to build one Arai helmet will take about 18 man-hours. All-day comfort All-day comfort with the Arai interior fit & shape together with the finest liner materials & the extensive ventilation system. & thanks to the perfect balance & weight distribution of the helmet, you hardly notice you are wearing an Arai. Penetration tested All Arai helmets are penetration tested, although not required by European helmet standards. The Arai penetration test is performed with a 3kg test cone that strikes from a height of 3m on the helmet. Double-D ring closure The flat & D-shaped rings fit smooth against the chin. No moving parts, no corrosion problems & just pulling the tab is enough to loosen the fastener. Smooth shape, better protection The smooth outer shell of Arai helmets is designed to glide without unnecessary resistance. You don’t want to decelerate your helmet more than necessary. That’s why all Arai vents & ducts are designed to break off during an impact. Hard outer shell, soft inner shell Arai uses a very hard outer shell to spread impact forces & a soft inner shell to absorb remaining energy. The multiple-density EPS inner shell is made using a unique technology of combining three to five densities in various areas as a single component. 5-year limited warranty All Arai helmets are warranted against defects in materials & workmanship, & are serviceable only for the properly fitted first user for 5 years from date of first use, but no more than 7 years from date of manufacture. Arai In-house test This Arai helmet is designed to meet the stringent Arai In-house standard requirements, in addition to mandatory standards such as ECE 22-05 & voluntary standards such as SNELL M2010. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default, even if it is shown differently. all helmets that have a visor will be delivered with a clear visor, even if it is shown differently.
...

The RX-7V is the crown of knowledge, experience & know-how in helmet technology from Arai. With a PB-SNC² outer shell, the revolutionary VAS (Variable Axis System) & a significantly softer area around the temples, the RX-7V is the milestone in the premium helmet segment. From the antimicrobial liner with even slimmer frame to the ducts, enhanced air diffusers & integrated air ducts, every single part is a testament to the attention to detail that is so typical of Arai. Arai has continuously enhanced the stall characteristics by learning from real-world accidents. Thanks to the stronger & smoother outer shell & VAS, the RX-7V is closer than ever to the ideal helmet shape. General PB-SNC2 outer shell Variable Axis System (VAS) Ventilation Free Flow System (FFS) Eyeport air duct Front ventilation Middle upper ventilation
- Inlet Diffuser System Forehead ventilation to temple area (innovative & offered exclusively by Arai) Chin ventilation with three positions Rear ventilation Exhaust vent at the neck Side exhaust vents Aerodynamics Pull-down chin spoiler Patented Air Wing® adjustable (innovative & offered exclusively by Arai) Visor VAS Max Vision visor with anti-fog option New locking lever for the visor Pinlock lens included Inner lining Antimicrobial material Replaceable cheek pads Replaceable inner liner Replaceable chinstrap covers Replaceable neck roll Speaker pockets Face Contour System (FCS) 5 mm Peel Away cheek pads 5 mm Peel Away temple padding Thin center pad for more space in the front area Comfort Emergency Release System (ERS) Breathing protection Chin wind deflector Homologation ECE 22-06 SNELL M2010/2015 RX-7V Ventilation New diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Shell Construction: PB-SNC2 Peripherally Belted Structural Net Composite Arai´s proprietary (super fibre belt) Peripheral Belt, borrowed from our F-1 technology, maximizes shell strength & flexibility while maintaining low weight. Positioned across the top of the eye port, this band allows the use of a thinner EPS liner which greatly enhances the upward field of view – especially appreciated in a full racing tuck! The Structural Net Composite adds a physical bond to the resin bond of the many layers of fibres & reinforcing materials within the shell. Variable Axis System (VAS) With VAS, the visor mounting position is lowered, yielding an average of an additional 24mm across both temple areas, in pursuit of the ideal smoother shape that increases the ability of glancing off energy. As a result, this has made it possible for more of the shell to be smoother along & above the test line of the Snell standard. Ventilation: Free Flow System (FFS) Creates airflow under the helmet that reduces wind noise & turbulence while increasing the exhaust of hot air. Ventilation: Eyeport Airchannel Enhanced air exhaust from the eye port area, pulled through dedicated air channel to side ducts, improving efficiency & reducing noise. Front Ventilation: Center top vent The new Top Vent provides 11% more airflow than the previous Vent. The new bigger switch makes opening & closing easier. The new Top Vent has three positions, closed, half open & fully open to adjust the airflow & prevent water intrusion when fully closed. Front Ventilation: Diffuser system The new diffusers are 20mm longer & straightened for enhanced aerodynamics, working together with the Air Wing to improve stability. Compared to the previous diffusers, the efficiency of the intake scoops of the new diffusers has increased by 19%. The new air intake vents not only have more adjustability with three positions, closed, half open & fully open but also help to improve sealing that decreases wind noise & water intrusion. Front Ventilation: Brow vents extended to temple area Fresh air can enter directly to the forehead area without the need for holes in this critical area of the shell & impact absorbing liner. For specific models the ventilation is extended to the temple area. Rear Ventilation: Neck exhaust vent To enhance hot-air extraction from the interior. Increases the ventilation effect at the lower part of the helmet. Rear Ventilation: Side exhausts Produce low pressure behind the rear vent for better hot air extraction. Integrated in the shell for better aerodynamics, reduce wind noise & prevent buffeting at speed. Inside, a small foam dam helps to absorb & diminish excessive noise, without reducing ventilation performance. Aerodynamics: Pull Down Chin Spoiler Helps minimize wind noise & also aids with the extraction of hot air from the face area. Provides additional deflection of road debris away from neck. Depending on the model the Chin Spoiler is retractable. Aerodynamics: Patented Air Wing® adjustable Moto GP tested & designed to greatly reduce drag, turbulence & buffeting resulting in more comfort & additional top-speed. It improves stability of the helmet at high speeds or when braking hard & reduces noise. Depending on the model the Air Wing is adjustable in five different angles of attack positions to suit every riding position. Visor: VAS Max Vision Visor with De-Mist option VAS MAX Vision shield is standard to provide better visibility in all seasons & for all types of riding. Comes standard with Clear anti-fog Pinlock insert to be installed as needed. Visor: Pinlock insert lens included Effectively prevents misting & fogging of the visor, even under extreme wet & damp conditions. May be cleaned & changed easily. Interior: Antimicrobial Liner New exclusive liner with antimicrobial stays fresher between cleanings. Interior: Replaceable Interior Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Replaceable Neckroll Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water & mild soap. Rinse well after cleaning & never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Facial Contour System (FCS) To offer an even better snug fit & enhancing the comfort to the lower jaw, the Facial Contour System (FCS) works with a foam spring support in the cheek pad that compresses & rebounds, providing the necessary support without excessive pressure. Interior: 5mm ’’ Peel Away’’ Ear cups/ Cheek pads Giving even more ability to craft the perfect fit & comfort, the cheek pads now feature a 5 mm peel away layer for added room if needed. Interior: 5mm ’’ Peel Away’’ Temple pad Arai´s peel-away temple crown pads give the option of 5 mm more interior with* if needed. Comfort: Emergency Release System (ERS) Allows easier access to an injured rider. By pulling the orange tabs integrated in the pads, the cheek pads slide out. Making helmet removal easier for trained medical personnel & rescuers. Minimising the risk of additional injury. Comfort: Breath guard Works in conjunction with the dual-pivot® chin vent to better direct fresh air to the inside surface of the shield while at the same time directing hot breath down & away from the inside surface of the shield. Comfort: Chin Curtain Attached to the bottom of the helmet, the new chin curtain helps to further accentuate the Egg-shape form. The curtain simultaneously blocks air intrusion from turbulent air below & increases negative pressure to enhance the exhaust function of FFS by drawing more air from the mouth area. The enhanced airflow reduces noise even further. Approval: ECE 22-06 The most widely used & required international helmet testing standard. This helmet is approved according to the latest version of the testing standard ECE 22-06. This is valid in more than 50 countries. Approval: SNELL M2010/2015 The American SNELL Memorial Foundation is an independent organisation, SNELL M2010 is their latest new, more shock-absorbent standard. For the M2010 standard a steel ball shaped rather like a tennis ball anvil is used, they also test with flat & “kerb” shaped anvils). The impact test area of SNELL is larger than that of ECE. Multiple impacts & a penetration test on random spots are used. Five times inspected Each Arai helmet goes through five separate quality-control depart­ments: after the shell is made, after painting & graphic completion, after assembly & two in-process inspections. Washable interior The premium quality interior of any Arai helmet can be easily cleaned, in place, with mild soap & lukewarm water. Handmade It can take up to five years for our experts to earn the right to create an Arai shell. Each shell can take up to 27 steps & to build one Arai helmet will take about 18 man-hours. All-day comfort All-day comfort with the Arai interior fit & shape together with the finest liner materials & the extensive ventilation system. & thanks to the perfect balance & weight distribution of the helmet, you hardly notice you are wearing an Arai. Penetration tested All Arai helmets are penetration tested, although not required by European helmet standards. The Arai penetration test is performed with a 3kg test cone that strikes from a height of 3m on the helmet. Double-D ring closure The flat & D-shaped rings fit smooth against the chin. No moving parts, no corrosion problems & just pulling the tab is enough to loosen the fastener. Smooth shape, better protection The smooth outer shell of Arai helmets is designed to glide without unnecessary resistance. You don’t want to decelerate your helmet more than necessary. That’s why all Arai vents & ducts are designed to break off during an impact. Hard outer shell, soft inner shell Arai uses a very hard outer shell to spread impact forces & a soft inner shell to absorb remaining energy. The multiple-density EPS inner shell is made using a unique technology of combining three to five densities in various areas as a single component. 5-year limited warranty All Arai helmets are warranted against defects in materials & workmanship, & are serviceable only for the properly fitted first user for 5 years from date of first use, but no more than 7 years from date of manufacture. Arai In-house test This Arai helmet is designed to meet the stringent Arai In-house standard requirements, in addition to mandatory standards such as ECE 22-05 & voluntary standards such as SNELL M2010. Note Please be aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default, even if it is shown differently. all helmets that have a visor will be delivered with a clear visor, even if it is shown differently.
...