Arai CT-F Honda Gold Wing, Jet Helmet

More protection, more comfort and a better fit thanks to extended lower sides. But all this without affecting that feeling of freedom and the excellent view only an open face helmet can offer. First thing you notice on the CT-F is the revolutionary adjustable peak. The challenge was to design a peak with excellent aerodynamic properties, yet offering efficient protection against sunlight and offering a stunning look. The Arai engineers succeeded to combine these requirements brilliantly. Shell Construction SFL Special Fibre Laminate Strict quality controlled construction using special fibre layers, crowded with fibres right to the shell surfaces and bonded with special resins formulated by Arai, to disperse impact energy over the widest possible area – the shell’s main job –
through strength, structural integrity and impact flexibility. Front Ventilation: Dual intake Designed for increased airflow and lower noise level, guiding fresh, cool air into the interior. Front Ventilation: Brow vents extended to temple area Fresh air can enter directly to the forehead area without the need for holes in this critical area of the shell and impact absorbing liner. For specific models the ventilation is extended to the temple area. Rear Ventilation: Neck exhaust vent To enhance hot-air extraction from the interior. Increases the ventilation effect at the lower part of the helmet. Rear Ventilation: Side exhausts Produce low pressure behind the rear vent for better hot air extraction. Integrated in the shell for better aerodynamics, reduce wind noise and prevent
buffeting at speed. Inside, a small foam dam helps to absorb and diminish excessive noise, without reducing ventilation performance. Interior: Replaceable Chinstrap covers Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water and mild soap. Rinse well after cleaning and never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider. Interior: Facial Contour System (FCS) To offer an even better snug fit and enhancing the comfort to the lower jaw, the Facial Contour System (FCS) works with a foam spring support in the cheek pad that compresses and rebounds, providing the necessary support without
excessive pressure. Interior: 5mm ’’Peel Away’’ Ear cups/Cheek pads Giving even more ability to craft the perfect fit and comfort, the cheek pads now feature a 5 mm peel away layer for added room if needed. Interior: 5mm ’’Peel Away’’ Temple pad Arai´s peel-away temple crown pads give the option of 5 mm more interior with* if needed. Approval: ECE 22-05 The most common helmet certification internationally, required by over 50 countries worldwide. Five times inspected Each Arai helmet goes through five separate quality-control depart­ments: after the shell is made, after painting and graphic completion, after assembly and two in-process inspections. Washable interior The premium quality interior of any Arai helmet can be easily cleaned, in place, with mild soap and
lukewarm water. Handmade It can take up to five years for our experts to earn the right to create an Arai shell. Each shell can take up to 27 steps and to build one Arai helmet will take about 18 man-hours. All-day comfort All-day comfort with the Arai interior fit and shape together with the finest liner materials and the extensive ventilation system. And thanks to the perfect balance and weight distribution of the helmet, you hardly notice you are wearing an Arai. Penetration tested All Arai helmets are penetration tested, although not required by European helmet standards. The Arai penetration test is performed with a 3kg test cone that strikes from a height of 3m on the helmet. Double-D ring device The flat and D-shaped rings fit smooth against the chin. No moving parts, no
corrosion problems and just pulling the tab is enough to loosen the fastener. Smooth shape, better protection The smooth outer shell of Arai helmets is designed to glide without unnecessary resistance. You don’t want to decelerate your helmet more than necessary. That’s why all Arai vents and ducts are designed to break off during an impact. Hard outer shell, soft inner shell Arai uses a very hard outer shell to spread impact forces and a soft inner shell to absorb remaining energy. The multiple-density EPS inner shell is made using a unique technology of combining three to five densities in various areas as a single component. Organic shape The organic shape of an Arai outer shell offers a more natural appearance, seals better and conforms more to the head’s natural shape for
improved comfort, fit and to help minimize wind turbulence. 5-year limited warranty All Arai helmets are warranted against defects in materials and workmanship, and are serviceable only for the properly fitted first user for 5 years from date of first use, but no more than 7 years from date of manufacture. Different outer shells Unlike many other manufacturers Arai provides one size outer shell for each two-helmet sizes for most models. Together with different shaped outer shells for different models it is almost impossible not to find the fit you are looking for. Arai In-house test This Arai helmet is designed to meet the stringent Arai In-house standard requirements, in addition to mandatory standards such as ECE 22-05 and voluntary standards such as SNELL M2010. Note Please be
aware, as long as nothing else is written in the item description: All helmets will be delivered only with the ECE certification by default all helmets that have a visor will be delivered with a clear visor, even if it is shown differently.